Disconnect Negative Terminal When Welding
Last Updated 6/01/2021
Speculation runs rife regarding whether the negative terminal of a vehicle’s battery should be disconnected before welding on that vehicle. The reason to do it is that it helps to prevent damage to the vehicle’s ECU and other electronics. Many people believe the negative terminal should be disconnected but cannot explain why it should be done. Other people believe disconnecting the battery terminal has no impact on the ECU since the ECU is still connected on both terminals and the affect of disconnecting the battery only isolates the battery and nothing else. They believe the idea to disconnect is simply an old wives’ tale with no valid reasons to substantiate it. So who is right?
Ohm’s Law: This is usually presented as the formula V= iR where V is voltage, i is current and R is resistance. It tells us that voltage is required for current to flow. If there is current flowing through a conductor then there must be a voltage across that conductor. It also tells us that current always flows when there is voltage applied across a resistance, which means current will flow everywhere through parallel paths and not just take the path of least resistance.
Kirchhoff’s Circuit Laws: This law states that the sum of the voltages around a continuous electrical loop must be zero and the sum of the currents into and out of an electrical node is zero. Regardless of the current flowing, regardless of parallel or alternative loops, the voltages around every unique loop must sum to zero and the currents through each node must sum to zero. This is analogous to, if you walk around a track which has varying elevation, no matter what route you take on that track and what levels of elevation you reach, if you end up at the same spot you started then your net elevation change is zero. Or if many people are walking into an intersection where you can turn left or right, then the sum of the people going left plus people going right is equal to the number of people who entered the intersection.
Below is a circuit diagram that depicts welding a vehicle. On the left is welding with the negative battery terminal connected and on the right is welding with the negative battery terminal disconnected. The resistor represents the car body. I have assumed the car battery voltage is 12V and the welder voltage is 100V. The actual voltages are irrelevant. The point is to see whether welding could damage the ECU and whether disconnecting the negative battery terminal would reduce that risk. All voltages are measured with respect to the battery’s negative terminal. The box labelled “ECU” is the engine control unit or engine management. This is the device we are trying to protect.
V1 is the voltage across the ECU with the negative battery terminal connected whilst welding. V2 is the voltage across the ECU with the negative battery terminal disconnected whilst welding. Kirchhoff’s laws and Ohm’s laws resolve the voltage at each point. The left side has a closed loop through the ECU where Kirchhoffs voltage law easily verifies the voltage across the ECU. The right side has an open loop where Kirchoff’s current law dictates that no current flows through the ECU and Ohm’s law determines that the voltage across the ECU is zero. Similarly Ohm’s law could be used in isolation with the open circuit interpreted as an infinite resistance.
So from the diagram we see that:
V1 = 112V
V2 = 0V
We see that in the left circuit the ECU is suffering from overvoltage and could be damaged. It is designed for 12V yet has 112V across it. The right circuit, with the negative battery terminal disconnected, there is no voltage across the ECU and therefore it does not experience any overvoltage.
But welders produce less than 100 volts you say? It doesn’t matter. I would have liked to use “x” for battery voltage and “y” for welder voltage and shown V1 > V2 but that might have been difficult to follow. The voltages are irrelevant. The point is V1 > V2.
You might think that the metal sheeting of a car body is such a good conductor that it will never be able to generate any significant voltage drop at the current levels typical of welding. What about all the transitions and joins, for example where a door bolts onto the main body? Or the body bolts onto the chassis? What is the capacitance, inductance and overall impedance of the car body? Impedance describes the complex ratio between voltage and current for alternating currents. When you first strike the welder it yields a step function which would generate a reaction different to what the steady state DC resistance would predict. A step function is made up of many high frequency components. Not only are there many high frequencies present, but the voltage would be high when first striking the arc. Before welding starts the voltage floats up to the open circuit voltage which is typically between 30 to 100V. When first striking the arc the full open circuit voltage is applied between the welding rod and the earth clamp. I’d suggest that ECU damage is most likely when first striking the arc and not during steady DC current flow.
You might argue that adequate earthing will maintain the body at zero potential throughout. Ohm’s law tells us that if current is flowing there must be voltage regardless of your earthing. Further, earthing does not control the resistance through the body and thus does not necessarily prevent potentially large voltage drops.
From this evaluation it is confirmed that welding a vehicle does risk damage to the ECU and disconnecting the battery’s negative terminal will mitigate that risk.
Why Does This Happen?
The problem lies with the ECU and the welder sharing a single conductor – the vehicle’s body. For the welder to push current through the body, it must impose a voltage across it regardless of how good your earthing is (Ohm’s law). With the battery connected there is a closed electrical loop where the voltage across the vehicle’s body could add to the battery’s voltage and cause an overvoltage condition at the ECU. With the battery’s negative terminal disconnected, the loop is broken, both terminals of the ECU will float to the same voltage and no overvoltage will occur regardless of the voltage across the vehicle’s body.
How to Minimize the Risk When Welding
– Disconnect the battery’s negative terminal. This breaks the loop through the battery so that possible overvoltages are reduced.
– Place the welder’s earth as close as possible to your welding work and ensure the earth has secure electrical contact with the vehicle. This minimizes the potential for voltage spikes through the vehicle.
– Some suggest disconnecting airbag connectors, although I have not heard of airbags being a problem if the battery is disconnected.
Any References to Verify?
The body repair section of the Toyota Hilux 05-10 Service and Repair Manual states:
“When welding, there is a danger that electrical components will be damaged by the electrical current flowing through the body. Before starting work, disconnect the negative terminal of the battery and ground the welder near the welding location of the body.”